JezK
Edit File: dh_auto_install
#!/usr/bin/perl =head1 NAME dh_auto_install - automatically runs make install or similar =cut use strict; use warnings; use Debian::Debhelper::Dh_Lib; use Debian::Debhelper::Dh_Buildsystems; use File::Spec; use Cwd; our $VERSION = DH_BUILTIN_VERSION; =head1 SYNOPSIS B<dh_auto_install> [S<I<build system options>>] [S<I<debhelper options>>] [S<B<--> I<params>>] =head1 DESCRIPTION B<dh_auto_install> is a debhelper program that tries to automatically install built files. It does so by running the appropriate command for the build system it detects the package uses. For example, if there's a F<Makefile> and it contains a B<install> target, then this is done by running B<make> (or B<MAKE>, if the environment variable is set). If there is a F<setup.py> or F<Build.PL>, it is used. Note that the Ant build system does not support installation, so B<dh_auto_install> will not install files built using Ant. In compat 15 or later, B<dh_auto_install> will use F<debian/tmp> as the default B<--destdir> and should be moved from there to the appropriate package build directory using L<dh_install(1)> or similar tools. Though if the B<single-binary> addon for L<dh(1)> is activated, then it will pass an explicit B<< --destdir=debian/I<package>/ >> to B<dh_auto_install>. For earlier compat levels then unless B<--destdir> option is specified, the files are installed into debian/I<package>/ if there is only one binary package. In the multiple binary package case, the files are instead installed into F<debian/tmp/>, and should be moved from there to the appropriate package build directory using L<dh_install(1)> or similar tools. B<DESTDIR> is used to tell make where to install the files. If the Makefile was generated by MakeMaker from a F<Makefile.PL>, it will automatically set B<PREFIX=/usr> too, since such Makefiles need that. This is intended to work for about 90% of packages. If it doesn't work, or tries to use the wrong install target, you're encouraged to skip using B<dh_auto_install> at all, and just run make install manually. =head1 OPTIONS See L<debhelper(7)/B<BUILD SYSTEM OPTIONS>> for a list of common build system selection and control options. =over 4 =item B<--destdir=>I<directory> Install files into the specified I<directory>. If this option is not specified, destination directory is determined automatically as described in the L</B<DESCRIPTION>> section. =item B<--> I<params> Pass I<params> to the program that is run, after the parameters that B<dh_auto_install> usually passes. =back =cut my $destdir; buildsystems_init(options => { "destdir=s" => \$destdir, }); # PROMISE: DH NOOP WITHOUT cli-options(BUILDSYSTEM) buildsystem(install) # If destdir is not specified, determine it automatically if (!$destdir) { my @allpackages=getpackages(); if (@allpackages > 1 or not compat(14)) { $destdir="debian/tmp"; } else { $destdir=tmpdir($dh{MAINPACKAGE}); } } $destdir = File::Spec->rel2abs($destdir, getcwd()); if (compat(10)) { # Ensure that all debian/<pkg> directories exist install_dir(map { tmpdir($_) } @{$dh{DOPACKAGES}}); } else { install_dir($destdir); } buildsystems_do("install", $destdir); =head1 SEE ALSO L<debhelper(7)> This program is a part of debhelper. =head1 AUTHOR Joey Hess <joeyh@debian.org> =cut